+ Reply to Thread
Results 1 to 1 of 1

Thread: 06+ Projector Color Flicker/Cutoff Mod

  1. #1
    nyckid
    Guest

    Icon33 06+ Projector Color Flicker/Cutoff Mod

    DISCLAIMER: TRY THIS MOD AT YOUR OWN RISK, THIS IS A MODERATE/ADVANCED MOD, THEREFORE A LOT OF DETAILS ARE LEFT OUT, MOST OF WHICH ARE SELF-EXPLANATORY.

    BEFORE YOU PROCEED MAKE SURE YOU UNDERSTAND: THE MORE COLOR THERE IS THE LESS LIGHT OUTPUT (FOREGROUND) YOU HAVE. ALSO WITH SIGNIFICANT COLOR BAND, YOU LOSE THE FLICKERING EFFECT THAT YOU SEE IN BMW/MERCEDES, SUCH THAT YOUR LIGHTS WILL APPEAR SOLID PURPLE OR BLUE INSTEAD OF A QUICK SPARK OF BLUE THAT YOU SEE IN OTHER CARS.

    Note for 06s, simply use a wrench set with 8mm sockets, turn counterclockwise on all 3 bolts until the projector is free, also remove igniter by turning counterclockwise and pull away from the projector. Make sure you disconnect the solenoid power clip at the bottom of the projector.

    To make it easy on yourself, remove the reflector bowl by removing the 4 screws in the rear of the projector.

    After removing the projector from the headlights, remove the shroud that's holding the Lens in place. Use a flat head and insert into the indents.



    After removing shroud and lens, you will see the glare guard that needs to be removed. Caution: This step proved to provide additional light, but also some glare effect. Experiment at your own risk



    A drill press is used in this DIY to ensure a clean cut of the glare guard.



    It should look like this when done.



    The output should look like this when done. (Phillips 85122+ HID bulb used)



    Second part of the mod is replacing the Fresnel lens that comes factory and replace it with a clear one from TSX projectors. (ebay for about $150~$200 ) OR HIDplanet.com and search on the buy/sell/trade forum for 2.5" clear lenses. TSX works best

    Stock



    To remove the lens from the TSX projectors, use a set of pliers and pull the clip towards you and upwards.



    Simply place the clear lens from TSX and place it in the factory projector and reinstall the factory shrouds over it. Make sure the shroud is secure and the lens does not rattle or shift.

    Clear lens installed



    The output with removed glare guard and clear lens.



    Now we will proceed to bend the factory cutoff shield.

    Photo 1


    Photo2


    Photo 3


    As you can see in photo 2, the shield is 90 degrees up right, and for softening the glare reasons, the factory projector came with dual cutoff. The shield both needs to be changed.

    This mod requires some playing around with the shield to really get the right result.

    Step 1: To make it sharper, push the front shield downwards(or dremel off), so it's not in the view of the light path, it's the one closer to you in photo 3.

    Step 2: Refer to Photo 1, curve the shield more so it appears to be more of a semi circle and push it slight forward.

    Step 3: Modify the Metal Guide piece so it looks like the following. This allows for the shield to sit higher than stock and eliminate the previous vibration problem from removing the guide all together.

    This creates a number of issues, the vibration is not completely eliminated and I think it's the nature of the design, secondly, the spacing of the guide creates a mountain below the cutoff that is not as well lit as the rest, this became more prominent when leaving the guide in place.





    Step 4: (THIS STEP NO LONGER NECESSARY IF YOU KEPT THE METAL GUIDE PIECE IN )

    The stock shield uses a metal tension mechanism to pull the solenoid upwards, and when power is applied, the solenoid pulls the shield down, creating high beams. The problem was the factory shield was held down partially by the metal spacer, by removing this spacer, the shield springs upwards and holding too much tension on the solenoid, preventing the pulling down to happen.

    Solution is to remove the shield by unscrewing the bottom two screws and push the shield downwards, so it appears more of an oval. Make sure you push down with two hands and ensure both sides are even. Reinstall the shield and test it out.



    Now the result should be like this:



    Nightshot






    Finally you can get the color you want

    Purple


    Blue
    Last edited by nyckid; Apr. 28, 2010 at 05:15 pm.

+ Reply to Thread

Similar Threads

  1. Has anyone done the 'Color Cut-Off' mod on their projectors?
    By nyckid in forum Body, Lighting and Cosmetics
    Replies: 11
    Last Post: Apr. 28, 2010, 04:04 pm
  2. How to aim 06+ projector headlights
    By kwon in forum Body, Lighting and Cosmetics
    Replies: 0
    Last Post: Feb. 13, 2010, 04:17 am

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts